M150 Laser Source
The M150 RF CO₂ laser is designed with a slab discharge configuration, with the M150 RF CO₂ laser achieving a peak power of over 375W. The M150 RF CO₂ laser deliver excellent beam quality and power stability. With short pulse rise and fall times, the M150 RF CO₂ laser significantly enhance production efficiency. The high peak power and superior beam quality make the M150 RF CO₂ laser an ideal choice for a wide range of material processing applications.
M150 Laser Source
The M Series RF CO₂ lasers is designed with a slab discharge configuration, with the M150 lasers exceeding 375W. This compact laser design integrates the RF power supply with the laser cavity, allowing for flexible installation options, either vertically or horizontally.
The M Series lasers deliver excellent beam quality and power stability. With short pulse rise and fall times, the M Series lasers significantly enhance production efficiency. The high peak power and superior beam quality make the M Series lasers an ideal choice for a wide range of material processing applications.
The M series RF CO₂ lasers is built on a universal platform, featuring standardized mechanical, electrical, and optical interfaces, along with common software and unified service and support. The power range extends from 100W to 500W.
Advantages
- Wide range of operating power
- High peak power
- Short power rise and fall time
- Excellent beam quality
- High power stability
- RF power supply can be Installed vertically or horizontally
Applications
- Marking
- Engraving
- Cutting
- Drilling
Specifications:
| MOEL | M100i | M100 | M150 |
| Wavelength (μm) | 9.3 | 10.6 | 10.6 |
| Output Power (W) | ≥ 90W | > 100W | > 150W |
| Power Range (W) | 10-90W | 10-100W | 10-150W |
| Peak Power (W) | 225W | 250W | 375W |
| Power Stability (%) | < ±6% | < ±6% | < ±6% |
| Mode Quality (M²) | M² < 1.3 | M² < 1.3 | M² < 1.3 |
| Beam Ellipticity | < 1.2:1 | < 1.2:1 | < 1.2:1 |
| Beam Diameter (mm) | 2.2 ± 0.6 | 2.2 ± 0.6 | 2.2 ± 0.6 |
| Full-Angle Beam Divergence (mrad) | < 7 | < 7 | < 7 |
| Typical Polarization (parallel to baseplate) | > 100:1 | > 100:1 | > 100:1 |
| Pulse Frequency (kHz) | 0 – 100kHz | 0 – 100kHz | 0 – 100kHz |
| RF Excitation Pulse Width Range (μs) | 2 – 1000μs | 2 – 1000μs | 2 – 1000μs |
| Duty Cycle Limit (%) | 0 ~ 60% | 0 ~ 60% | 0 ~ 60% |
| Pulse Rise/Fall Time (μs) | ≤ 90μs | ≤ 90μs | ≤ 90μs |
| Weight | 22.8kg | 22.8kg | 22.8kg |
| Dimensions (L x W x H) | 908.4 x 164.6 x 134.8 mm | 908.4 x 164.6 x 134.8 mm | 908.4 x 164.6 x 134.8 mm |
| Cooling | Water | Water | Water |
| Heat Load (W) | < 2400W | < 2400W | < 2400W |
| Input Power | |||
| DC Input Voltage (VDC) | 48VDC | 48VDC | 48VDC |
| Continuous DC Input Current (A) | 50A | 50A | 50A |
| Environment Condition | |||
| Maximum Case Temperature | 5°C ~ 40°C | 5°C ~ 40°C | 5°C ~ 40°C |
| Temperature | < 50°C | < 50°C | < 50°C |
| Altitude | < 2000m | < 2000m | < 2000m |
| Humidity | < 80%, Non-Condensing | < 80%, Non-Condensing | < 80%, Non-Condensing |
| Shipping/Storage Environment | -10°C ~ 60°C, Non-Condensing | -10°C ~ 60°C, Non-Condensing | -10°C ~ 60°C, Non-Condensing |
| Coolant | |||
| Dynamic Coolant Flow Rate (l/min) | 6L/min | 6L/min | 6L/min |
| Coolant Maximum Static Pressure (kPa) | 210-500kPa | 210-500kPa | 210-500kPa |
| Coolant Setpoint Temperature Range | 20°C – 30°C | 20°C – 30°C | 20°C – 30°C |
| Hardness of water (CaCO3) | < 250mg/L | < 250mg/L | < 250mg/L |
| Notes: Measured at 10 kHz PRF, 60% duty cycle after a 5 minutes warm-up from cold start. Power Stability definition: At a constant water temperature, ±(Pmax – Pmin)/(2Pmax). Measured at the position of shaping lens light outlet. Measured at 10 kHz PRF and 60% duty cycle operation, maximum average input current. |
|||
